60" Full Auto Hot Cold Laminator Heat Assisted Wide Format Laminating Machine US

Description

60" Full - auto Low Temp Wide Format
cold laminator Laminating Machine
3 years warranty!
This price is only for the local pick up,if you are far from our warehouse,we can ship it to you,but extra shipping cost will be needed.
Description:
This 60" Full - auto Low Temp
Wide Format
cold laminator
with Stand can be widely used for pre - masking vinyl graphic, mount prints on substrate, over laminating inkjet prints and so on.
The cold laminator is used to after printing. Available for photographic, Ad. Shop and copy shop to do lamination work, adding a protective layer on books cover, photographic, color pages, documents, charts, drawings, indoor advertising products, etc.
This laminator 1600C6+ is low heated cold laminator
with liner and without
liner, a wide range of application.
It can be used
both cold laminating and hot laminating
with low temperature, to strip coil backing paper,to roll picture
automatically.
Especially when work in hot laminating conditions,it will improve the
coating effect by heating the roller,.
It’s multiple-function,easy operation and high efficiency.
Features:
Adopts low temperature cold laminating, mainly used to solve the issue that cold laminated images are hazy.
Stainless steel feeding table
130mm (5") upper rubber roller
Auto – take – up system
Anti – tilt and anti – fold device (Origin)
Pressure and height adjust hand wheel
Infrared temperature control device
This laminator comes with 2 pcs heating glass tube in the package.
Model
SEC-010
Maximum Laminator Width
1520mm (60")
Roller’s Diameter
130mm (5")
Maximum Laminating Thickness
25mm (0.99")
Maximum Heating Temperature
when hot laminating, the temperature is 50~60 degree, the highest
temperature is 60 degree.
Laminating Speed
From
0 to 10m (393")
per minute
Preheating Time
5 - 10mins
Power Consumption
0.3 - 0.5KW / h
Power Input
2200W
Height Adjust
Single side lifting link
Motor Forward / Reverse
Yes
Floor Stand
Yes
Auto Rewind Liner Pickup
Yes
After Laminating Pickup
Yes
Emergency Stops
Yes
Safety Photocell
Yes
Power Supply
AC110V, 50 / 60Hz
Control Panel
Instruction:
Preset temperature: Find out hot/cold framed switch, choose the "hot ", temperature display screen will light up, the left number is preset temperature, the right number is roller temperature, press “■ SET”key and then through “▲ UP” and“▼
DOWN” adjust preset temperature, after adjust it and press“■ SET”key confirm it. when cold film, the preset temperature is 50 ℃ .,the max temperature is 50 ℃.According to the viscosity of the glue, and adjust preset temperature.
Turn: This machine don’t have continuous reverse function;
In the "continuous" state it only can " turning";
In the "point move" state, through the pedal switch can "turning" or "reverse".
Governor knob: clockwise to grow speed, counter-clockwise to slow down; Please select the appropriate speed to ensure the laminating effect, when stop coated please select "point move".
A-Pressure adjusting valve
B-Pressure adjusting valve
C-locking screw nut
1. When the parallelism gap of the rollers is slight, it can be adjusted by the following method:
a. Moving screw A to adjust the balance of the roller while it ’ s rising. Find out which side of the roller rises slower, then move the screw outward ( Or find out which side rises faster, then move the screw inward). Then raise and lower the roller until the roller is balanced.
b. Move screw B to adjust the balance of roller while it’ s falling. Find out which side of the roller falls slower, then move the screw outward ( Or find out which side falls faster, then move the screw inward). Then raise and lower the roller until the roller is balanced.
(Adjust the air pressure to 0.1MPa, the movement of the roller is slower than normal. It’s convenient to observe. )
Attention: after the aujustment, the lock screw nut.must be fixed.
2. When the parallelism gap is big, it can be adjusted by the following method:
a. Loosen the lock screw nut on both sides and move outward completely;
b. Move 4 pressure adjusting valve softly inward completely, please keep the power
used same at 4 times.
c. Move 4 pressure adjusting valves same laps outward, 5 and half laps is the best
normally. But the laps can be adjusted according to the real situation. But the laps
moved outward must be same, which is good for adjustment.
d. Now, the parallelism is slight, Method 1 can be used to adjust then
Attention: While adjusting parallelism gap, only one side of the roller
should be referred, then adjust the pressure adjusting valve on the other side to
make the roller reach balance. Don’t adjust 2 pressure adjusting valve together.
Film laminating
Laminating work is an extremely fine, technical stronger work, for beginners should have experience in the technicians under guidance of Membranae tectoria work, the below only show the general operation.
Preheating ready to work:
1. Fall down tne upper nip roller;
2. Press the "continuous" and "turning" switch, governor rotate to the "1";
3. Open the main switch;
4. Open the "hot" switch and et the heat temperature which we required, then nip roller began to heating. Hot laminating, the preset temperature is 90 ℃ , when low temperature/cold laminating, the preset temperature set to 45 ℃ (to working temperature need about 10-20 minutes)
5. Take out a roll of film and install into material roller, then let roll into material feeding roller scaffold and pulling the film with the hand, shall ensure the appropriate resistance,through the next to the damping handwheel adjust it.
6. Let framed chart scroll in carton, then packed in rewinding stent and fixed them.
When the up roller reach a set temperature:
(1). Press the "point move" switch and then nip roller will stop turning.
(2). Let remove pressure paper stem and lift the above roller.
(3).(hot film installation)
(4). (cold film installation) Generally do not need to heat, when cold framed film used
for cold framed, but if the above nip roller heating to 40-50℃, cold Membranae
tectoria effect will be better. The Membranae tectoria put out and from between two
nip roller through winding (paste) on the picture roll (just apply to beginning not
skilled);Or someone pulled, after laminating starting, and then flat longer fast around
(paste) in the picture roll. In proper position with paper cutting knives let membrane
and back paper apart, then stir up a paper upper the back and make it apart from film, with adhesive tape to fixe at the back of paper roll by level. Note: When the back
paper after separation film
should be no paper folding and film tightly with nip roller surface to keep level.
(5). Put the needed laminating paper on the front working table, insert the blank of
paper in between rollers , then put press-paper roller.
(6). Put down the upper roller (the handwheel is very relaxed, left and right don't
force). Note: the two sides of the picture with edge roller vertical, lestthe laminating process
go partial.
7. Press the "continuous" switch and began to laminating.
Note: if the hot film without drying, clockwise rotation handwheel
increase friction damping and improve the swelling force.
8. Clockwise governor knob and adjust to the appropriate speed.
Note: the faster speed the faster cooling roller, please choose the
appropriate membranae tectoria temperature and speed.
If the plastic film show the wrinkles and need to stop, cutting film and stall into the
film again. When film laminating should pay the below five attention:
1. The film should be wrapped around the picture roll.
2. Scroll to framed chart in carton, after stalled in rewinding stent around the film
and alignment and then fixed.
3. The pictures inserted between rubber roller, pictures must tighten, tile in front of
countertop, pictures with table on both sides of the length direction must be show
90°angle state and guarantee membranae tectoria didn't skewed coated.
4. When membranae tectoria if done correctly and the picture is still running
deviation, with the hand press run folk prescription pictures,artificially increase
pressure and adjust it slowly.
5. When membranae tectoria should pay attention to adjust roller coated
materials,rewinding bracket, the paper roll back, and get the picture roll damping and
in order to keep the reasonable friction, which relate to plastic roller effect.
The general questions and methods
Problem
Reasons
Methods
Control panel have no electricity
Power is off or "emergency" button down
Check the power and emergency button
Fuse tube broken
Fuse tube broken Check and replace insurance pipe
Don’t turn
Force between rollers too large
Lift a little the upper roller
Friction is too large
Adjust friction
Motor key loosen or fall off
Tighten sprocket key
Motor or speed knob get problem
Contact with motor or governor
Laminated paper isn't clear and have white point
Roller temperature is not enough
Increase roller temperature
Dust on the paper
Clean the dust
Film quality not good
Contact suppliers to replace film
laminated paper have pleated bubbles
Roller's force is not uniform or too much
Adjust roller force
Paper not flat
Put paper in 90 angle into rubber roller
Speed slow and temperature too high
Increase speed and reduce temperature
Press-paper roller not in the right position
Press-paper roller fully touch paper
Laminated paper continuous running aslant
Roller force is not evenly on both sides
Adjust the roller force
Paper at first not straight
Make the paper straight
Film fold
Film tension is too small
Adjust material-roller's resistance
The upper roller's temperature too low
Adjust to the required temperature
laminated paper curly seriously
Film's tension is excessive
Adjust to suitable tension
The winding tension is too large
Adjust to suitable tension
Package:
The laminator comes with 2pcs of heating glass tube, 1pcs is on the machine, 1 pc is in
another package. We send the spare 1 pc of it just in case of any damage during the
shipping.
If the one on the machine damaged, please use the spare 1 pc replace it.
We will not accept any complaint of the tube damaged.
Machine Dimension
74" x 27" x 45" (1880mm x 680mm x 1140mm)
Machine Weight
280lb (140kg)
Package
Fumigation free package
Packing Size
81" x 28" x 28" (2060mm x 710mm x 720mm)
Gross Weight
441lb (200kg)
Table 1: Accessories
Term
Quantity
Notice
Backing sheet reception roll
1
Feeding roll
1
Film roll
1
Black rubber beam weight
1
Finished products roll
1
Hand wheel
1
Rubber mat
1
Left support of feeding roll
1
Right support of feeding roll
1
Fuse
4
2A/7A
Video
1
Table 2: Steel stand packing list
Item
Quantity
Notice
Steel beam
2
Middle steel beam
1
Left leg
1
Foot wheels contained
Right leg
1
Foot wheels contained
Hex screw M8 x 80
12
Flat mat φ8
12
Bounce mat φ8
12
Application
Applying to indoor and outdoor car sticker,photo and video,rimless no painting mounting and so on.
SHIPPING
1.We will ship your item by FedEx, DHL, UPS, EMS, e-Package etc with the tracking number showed on ebay.
2.Your item will be shipped within 1-3 working days after clear payment .
3.The shipping time varies. If by FedEX, DHL,or UPS, 3-4 business days to USA,5-7 business days to other most countries.
If by e-packet,7-15 days to USA,and 2-4 weeks to other most countries.
4.Due to the local dispatch or other reasons, sometimes the shipping time will be delay. Please kindly understand Uncertainties by the delivery company.
5.
If you have not received your shipment within 30 days from payment, please contact us. We will track the shipment and get back to you in 24 hours.
Our goal is best customer satisfaction!
PAYMENTS
1. we accept: Paypal, Please contact us if you may need some other payment method.
2. We will very appreciate if you can pay for the order after your ordering within 1-3 working days so that we can provide you the best services.
3. Please list your special requests in message after payment. (color, packages, etc.)
4.S&H will be determined based upon your address. PLEASE NOTE: S&H DOES NOT INCLUDE DUTIES, LOCAL TAXES OR ANY OTHER IMPORT FEES.
Feedback
1.If you have any problems or concerns to your order or products, please message us and give us a chance to assist before you leave negative feedback.
2.We believe that we can produce a positive outcome to any situation to earn your like
s.
3.Your satisfaction is guaranteed.
Thanks for your business ！